« previous next »
Pages: [1]   Go Down

Author Topic: Arm Lift Support DeWalt 788  (Read 3784 times)

Offline TuckerBoy2000

  • *
  • Newbie
  • Posts: 8
    • View Profile
Arm Lift Support DeWalt 788
« on: November 09, 2019, 02:27:12 pm »
I have bought a DeWalt 788 and I was wondering if there was a way to support the arm when placing blade through hole? Thanks much in advance.
Logged

Offline Judy Hunter

  • *****
  • Hero Member
  • Posts: 2694
  • The world moves on.
    • View Profile
    • Artistic Sawdust and Other Fun Stuff
Re: Arm Lift Support DeWalt 788
« Reply #1 on: November 09, 2019, 10:29:56 pm »
I have The Dewalt saw and have tried other "lifters" and they were junk or wore out way too soon.
I The one I have now is GREAT!!

Called "THE LIFTER"
papasworkshop.org
Logged
I'm from North Dakota

Offline jscott2

  • *****
  • Hero Member
  • Posts: 521
    • View Profile
Re: Arm Lift Support DeWalt 788
« Reply #2 on: November 10, 2019, 10:18:53 am »
I have the Jim dandy lifter. https://jimdandy.com/collections/all-products/products/easy-lift-system-for-dewalt-scroll-saw-dw788. It works well for me and has given no trouble. YMMV.

Good luck selecting a lifter.
Jim
Logged
Using a Delta 40-690 in the Montreal, Quebec (Canada) area

Offline Silver Sliver

  • *
  • Newbie
  • Posts: 47
    • View Profile
Re: Arm Lift Support DeWalt 788
« Reply #3 on: November 10, 2019, 11:30:18 am »
On my Delta 40-694 clone I used a short length of a 2x4 between the arm and the table.  Worked very well for me.
Logged

Offline Jimm

  • *
  • Newbie
  • Posts: 23
    • View Profile
Re: Arm Lift Support DeWalt 788
« Reply #4 on: November 10, 2019, 05:08:25 pm »
I bought a length of aluminum at the big box store lifted the saw head eyeballed where to drill two holes for mounting it and then bent it away from head. Hooks under existing screw and works great. Same as the lifter but cost me about 4 dollars.
Logged

Offline TuckerBoy2000

  • *
  • Newbie
  • Posts: 8
    • View Profile
Re: Arm Lift Support DeWalt 788
« Reply #5 on: November 10, 2019, 05:13:45 pm »
I want to thank everyone for their reply. I have been using a short 2x4 which works okay, so I may stay with it until I check out all the suggestions. Once again, thanks all.
Logged

Offline saw duster

  • *
  • Newbie
  • Posts: 2
    • View Profile
Re: Arm Lift Support DeWalt 788
« Reply #6 on: December 12, 2019, 10:56:27 am »
I tighten the screws that hold the arm in place, and when I lift it, it stays up while I feed the blade through the holes.
Logged

Offline Jimmy2

  • *
  • Newbie
  • Posts: 16
    • View Profile
Re: Arm Lift Support DeWalt 788
« Reply #7 on: December 12, 2019, 01:30:05 pm »
This is the one I have https://www.bearwood.com/scroll-saw-lifter-dewalt.html I got mine from Hector Garcia Facebook page.  Before this I used Dee & Walt from Steve’s pattern catalog ;D
Logged

Offline new2woodwrk

  • *
  • Newbie
  • Posts: 8
    • View Profile
Re: Arm Lift Support DeWalt 788
« Reply #8 on: December 30, 2019, 08:03:56 pm »
I use a simple shorty 2x4 - it was free and works great!
Logged

Offline Berta

  • **
  • Jr. Member
  • Posts: 50
    • View Profile
Re: Arm Lift Support DeWalt 788
« Reply #9 on: December 31, 2019, 06:50:02 am »
Steve Good actuality has a cute pattern for a gir or boy that holds the arm up. “Dee” and “Walt”.
Logged
Pages: [1]   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj