« previous next »
Pages: [1]   Go Down

Author Topic: Morgan - finally got around to it  (Read 2163 times)

gilljc

  • Guest
Morgan - finally got around to it
« on: April 03, 2014, 12:24:13 pm »
Want to say thanks to EIEIO for the patterns, my baby bandsaw wasn't up to cutting the compound pattern, but the morgan looks nice as a keyrack, done in local oak, unfinished as yet
Logged

Offline Al W

  • *****
  • Hero Member
  • Posts: 2535
    • View Profile
Re: Morgan - finally got around to it
« Reply #1 on: April 03, 2014, 02:55:15 pm »
Another nice one.   Thanks.


Al
Logged
Molon Labe

Believe half of what you see, and none of what you hear.

The government is NOT always right, or on your side.

Offline DWSudekum

  • *****
  • Hero Member
  • Posts: 3677
    • View Profile
    • The DW Collection
Re: Morgan - finally got around to it
« Reply #2 on: April 03, 2014, 03:25:00 pm »
Nicely done.  Thanks for sharing this with us.


DW
Logged
Life is tough, it is even tougher if you are stupid  -  John Wayne

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: Morgan - finally got around to it
« Reply #3 on: April 03, 2014, 06:42:08 pm »
that's a great idea, making it into a coat rack. The cutting looks swell - is the wood thick? Looks like about 3/4".

The compound version really needs a bandsaw for the 1st cut unless you shrink the scale to tiny.
Logged
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Offline wombatie

  • *****
  • Hero Member
  • Posts: 5557
  • Victoria Australia
    • View Profile
Re: Morgan - finally got around to it
« Reply #4 on: April 04, 2014, 12:52:10 am »
You did a great job, it looks great.

Marg
Logged
MARG

No one notices what I do until I'm not here to do it............

gilljc

  • Guest
Re: Morgan - finally got around to it
« Reply #5 on: April 04, 2014, 03:12:34 am »
Again, thanks to Ray for the pattern, is about 7" x 4" by just under half inch thick my bits of wood are all less than 5" wide, so limited to wee things
Logged

Offline frankorona

  • *****
  • Hero Member
  • Posts: 4030
  • Frankorona (Frank) (Crown)
    • View Profile
    • Frankorona?s workshop
Re: Morgan - finally got around to it
« Reply #6 on: April 04, 2014, 08:49:48 am »
Very good work, original and well done, thanks for sharing.
Logged

Rover2

  • Guest
Re: Morgan - finally got around to it
« Reply #7 on: April 04, 2014, 08:54:49 pm »
Looks really nice.  I like the way you made it as a coat rack.  Thanks for sharing it with us.
Nice pattern Ray.
Logged

Offline Keefie

  • *****
  • Hero Member
  • Posts: 4550
    • View Profile
Re: Morgan - finally got around to it
« Reply #8 on: April 05, 2014, 03:13:29 am »
Great work there, and very ingenious to turn it into a coat rack - very nicely done.  Nice pattern too Ray.
Logged
It's all a case of "Mind over Matter",  The Government don't Mind, and I don't Matter.

Offline Marcellarius

  • *****
  • Hero Member
  • Posts: 6135
  • Scrolling each day, keeps the doctor away
    • View Profile
    • Some of my work
Re: Morgan - finally got around to it
« Reply #9 on: April 05, 2014, 05:50:55 am »
that's a great project, nice grain in the wood.
Logged
Marcel

sometimes I make designer firewood....

Offline newfie

  • *****
  • Hero Member
  • Posts: 5037
  • The Way I Scroll
    • View Profile
    • some of my woodworking
Re: Morgan - finally got around to it
« Reply #10 on: April 16, 2014, 06:07:02 pm »
nice work
Logged


excalibur 21
Every woodworker needs a fireplace

Offline Merlin

  • *****
  • Hero Member
  • Posts: 1191
    • View Profile
Re: Morgan - finally got around to it
« Reply #11 on: April 17, 2014, 07:25:23 am »
Very nice cuttin and the pattern is great also, was it made available on site cause I musta missed it.

***Merlin***
Logged
Try not! Do,
or do not
There is no try

Yoda "Empire Strikes Back" 1980

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: Morgan - finally got around to it
« Reply #12 on: April 17, 2014, 10:30:55 am »
Merlin - the pattern was not as a key hook, but here it is...
Logged
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Offline Merlin

  • *****
  • Hero Member
  • Posts: 1191
    • View Profile
Re: Morgan - finally got around to it
« Reply #13 on: April 17, 2014, 04:30:57 pm »
Thanks Ray much appreciated.

***Merlin***
Logged
Try not! Do,
or do not
There is no try

Yoda "Empire Strikes Back" 1980
Pages: [1]   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj