« previous next »
Pages: [1] 2   Go Down

Author Topic: Filigree Crosses  (Read 2689 times)

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Filigree Crosses
« on: February 26, 2014, 02:37:03 pm »
These are the Filigree Cross designs that Sheila was kind enough to post last Easter - that time's coming up again. They are scaled up to 5" wide and cut from 1" thick birch using several FDUR#5 blades (this wood is really hard). The stand is a bent piece of 3/32" welding wire stuck into a 2"x2.5"x1" birch base. Finished with Feed n Wax. They are headed to this weekend's Mardi Gras Silent Auction at our parish.
   
Logged
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Malistar22

  • Guest
Re: Filigree Crosses
« Reply #1 on: February 26, 2014, 02:39:38 pm »
Looks pretty slick!
Logged

Offline Keefie

  • *****
  • Hero Member
  • Posts: 4550
    • View Profile
Re: Filigree Crosses
« Reply #2 on: February 26, 2014, 02:49:30 pm »
They look great, I'll have to try to find that pattern from Sheila
Logged
It's all a case of "Mind over Matter",  The Government don't Mind, and I don't Matter.

Offline DWSudekum

  • *****
  • Hero Member
  • Posts: 3677
    • View Profile
    • The DW Collection
Re: Filigree Crosses
« Reply #3 on: February 26, 2014, 02:50:51 pm »
Excellent job on them.  Shrink the pattern so that the cross is around 4 inches tall and put a loop on the top and then cut it from 1/4 in. stock and you could have a necklace.  Shrink it even further to around 1 1/2 inches and you could make earrings.  Thanks for sharing these with us.


DW
Logged
Life is tough, it is even tougher if you are stupid  -  John Wayne

Offline mickey357

  • *****
  • Hero Member
  • Posts: 692
    • View Profile
Re: Filigree Crosses
« Reply #4 on: February 26, 2014, 03:57:45 pm »
Nice job on the cuttin'. Love the patterns. They should bring a lot of $$$. Good luck on the Mardi Gras Silent Auction .
Logged

countryscroller

  • Guest
Re: Filigree Crosses
« Reply #5 on: February 26, 2014, 08:43:13 pm »
Very nice!
Logged

Offline Al W

  • *****
  • Hero Member
  • Posts: 2535
    • View Profile
Re: Filigree Crosses
« Reply #6 on: February 26, 2014, 09:46:52 pm »
Nice work Ray.  Thanks for sharing.

Al
Logged
Molon Labe

Believe half of what you see, and none of what you hear.

The government is NOT always right, or on your side.

Offline wombatie

  • *****
  • Hero Member
  • Posts: 5557
  • Victoria Australia
    • View Profile
Re: Filigree Crosses
« Reply #7 on: February 27, 2014, 12:50:25 am »
They look terrific Ray.  They will have high bid at the auction I am sure.

Marg
Logged
MARG

No one notices what I do until I'm not here to do it............

Offline frankorona

  • *****
  • Hero Member
  • Posts: 4030
  • Frankorona (Frank) (Crown)
    • View Profile
    • Frankorona?s workshop
Re: Filigree Crosses
« Reply #8 on: February 27, 2014, 07:58:52 am »
Excellent work, very well done, another big hit, thanks for sharing. ;)
Logged

Offline Toneman

  • *****
  • Hero Member
  • Posts: 1100
    • View Profile
    • TLC Miniature Horse Farm
Re: Filigree Crosses
« Reply #9 on: February 27, 2014, 08:26:19 am »
Very nice Ray!

Tony,aka,Toneman
Logged

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: Filigree Crosses
« Reply #10 on: February 27, 2014, 10:00:07 am »
Quote from: DWSudekum on February 26, 2014, 02:50:51 pm
Excellent job on them.  Shrink the pattern so that the cross is around 4 inches tall and put a loop on the top and then cut it from 1/4 in. stock and you could have a necklace.  Shrink it even further to around 1 1/2 inches and you could make earrings.  Thanks for sharing these with us.


DW
Thanks all. DW - I think the originals from Sheila were meant to be small. I cut some last year in 1/4" rosewood for some friends. I think they were about 2" wide. The rosewood is very dense, so they had a nice weight to them. I did not try earrings, but I'd pay a dollar for some that small - that would be some intricate cutting. :)
Logged
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Offline Intarsia92

  • *****
  • Hero Member
  • Posts: 1617
    • View Profile
Re: Filigree Crosses
« Reply #11 on: February 27, 2014, 11:57:43 am »
The crosses look beautiful, great patterns.
Logged
Al

Hegner 20" Polymax

Offline heiko rettberg

  • *****
  • Hero Member
  • Posts: 1566
    • View Profile
Re: Filigree Crosses
« Reply #12 on: March 02, 2014, 05:54:18 am »
came out grate, very nice.
Logged

Offline newfie

  • *****
  • Hero Member
  • Posts: 5037
  • The Way I Scroll
    • View Profile
    • some of my woodworking
Re: Filigree Crosses
« Reply #13 on: March 02, 2014, 07:56:11 am »
nice work
Logged


excalibur 21
Every woodworker needs a fireplace

Offline Marcellarius

  • *****
  • Hero Member
  • Posts: 6135
  • Scrolling each day, keeps the doctor away
    • View Profile
    • Some of my work
Re: Filigree Crosses
« Reply #14 on: March 02, 2014, 11:13:05 am »
great job Raymond, really love them.
Logged
Marcel

sometimes I make designer firewood....
Pages: [1] 2   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj