Author Topic: Elizabeth Taylor Portrait  (Read 1543 times)

Spartan scroller

  • Guest
Elizabeth Taylor Portrait
« on: November 26, 2013, 11:22:27 am »
Does anyone have or know where I may find an Elizabeth Taylor portrait pattern?

Thanks,
Terry
terrysscrollshoppe.com
facebook.com/terrysscrollshoppe

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: Elizabeth Taylor Portrait
« Reply #1 on: November 26, 2013, 12:43:10 pm »
From this glamore shot. This is a Threshold rendering - my favorite type.
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Spartan scroller

  • Guest
Re: Elizabeth Taylor Portrait
« Reply #2 on: November 26, 2013, 01:38:25 pm »
Thanks E:
That should do it!

Regards,
Terry

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: Elizabeth Taylor Portrait
« Reply #3 on: November 26, 2013, 01:42:50 pm »
Please post a photo if you cut it.
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Offline chelcass

  • *****
  • Hero Member
  • Posts: 1355
    • View Profile
Re: Elizabeth Taylor Portrait
« Reply #4 on: November 26, 2013, 05:05:13 pm »
Great pattern, snagged a copy.  thanks
ChelCass

Offline wombatie

  • *****
  • Hero Member
  • Posts: 5557
  • Victoria Australia
    • View Profile
Re: Elizabeth Taylor Portrait
« Reply #5 on: November 27, 2013, 04:55:35 am »
Wow Ray that is a beautiful pattern

Marg
MARG

No one notices what I do until I'm not here to do it............

Offline frankorona

  • *****
  • Hero Member
  • Posts: 4030
  • Frankorona (Frank) (Crown)
    • View Profile
    • Frankorona?s workshop
Re: Elizabeth Taylor Portrait
« Reply #6 on: November 27, 2013, 07:54:57 am »
?Wow! Wonderful pattern, thanks for sharing

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: Elizabeth Taylor Portrait
« Reply #7 on: November 27, 2013, 01:51:52 pm »
Note to any cutters. I forgot to mention at the time I posted this - the threshold rendering often produces one or more BIG peninsulas. On this pattern, Liz's face is held in place by a single very small bridge at her chin. I suggest you leave a temporary bridge about where you might have a part in hair or near the ears, then cut it out as your last cut. You could also leave the hair for the last cut, but it's a big, complex piece and might cause a break.

I have not tried to cut this, so I'd appreciate seeing one that someone finished.
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Offline Martin

  • ****
  • Sr. Member
  • Posts: 276
    • View Profile
Re: Elizabeth Taylor Portrait
« Reply #8 on: November 30, 2013, 10:14:06 am »
I really like this pattern and just had two goes at it, but both times I broke it where the arrow is. Must remember to do the delicate bits first. :)

 

SMF

Teknoromi