« previous next »
Pages: [1] 2   Go Down

Author Topic: Fretwork pedestal table  (Read 4024 times)

Offline RFortier

  • **
  • Jr. Member
  • Posts: 68
    • View Profile
    • Sparetime Scroller
Fretwork pedestal table
« on: October 15, 2013, 10:36:45 pm »
I've been working on this project on and off for the last couple of months and finally finished it. This is from a pattern by Dan Wilckens. I'm really happy with the way it turned out. It's been quite a challenge but well worth it. I installed lights inside but they are a little bright so I'm going to try to find something different to light it.

Next I'm going to work on a fretwork clock to put on top of the table. That will be a good winter project.

Thanks for looking.

Ray F
Logged

hotshot

  • Guest
Re: Fretwork pedestal table
« Reply #1 on: October 15, 2013, 11:08:58 pm »
Absolutely beautiful, goodness.  I wish I could see that in person.  Good work  -----Randy
Logged

Offline Keefie

  • *****
  • Hero Member
  • Posts: 4550
    • View Profile
Re: Fretwork pedestal table
« Reply #2 on: October 16, 2013, 04:20:10 am »
AWESOME - that is absolutely beautiful.
Logged
It's all a case of "Mind over Matter",  The Government don't Mind, and I don't Matter.

Offline DWSudekum

  • *****
  • Hero Member
  • Posts: 3677
    • View Profile
    • The DW Collection
Re: Fretwork pedestal table
« Reply #3 on: October 16, 2013, 05:58:16 am »
Very nicely done Ray.  That looks like something I have seen in some of the ornate churches.  Looking forward to seeing the rest of your "winter" project.  Thanks for sharing this with us.

DW
Logged
Life is tough, it is even tougher if you are stupid  -  John Wayne

Offline newfie

  • *****
  • Hero Member
  • Posts: 5037
  • The Way I Scroll
    • View Profile
    • some of my woodworking
Re: Fretwork pedestal table
« Reply #4 on: October 16, 2013, 07:07:33 am »
WOW great work thanks for sharing
Logged


excalibur 21
Every woodworker needs a fireplace

countryscroller

  • Guest
Re: Fretwork pedestal table
« Reply #5 on: October 16, 2013, 07:27:24 am »
Fantastic work!!! Thanks for sharing.
Logged

Offline frankorona

  • *****
  • Hero Member
  • Posts: 4030
  • Frankorona (Frank) (Crown)
    • View Profile
    • Frankorona?s workshop
Re: Fretwork pedestal table
« Reply #6 on: October 16, 2013, 07:40:19 am »
Awesome job!!! looks great, thanks for sharing.
Logged

Offline heiko rettberg

  • *****
  • Hero Member
  • Posts: 1566
    • View Profile
Re: Fretwork pedestal table
« Reply #7 on: October 16, 2013, 08:27:30 am »
only i can say is wow, fantastic Job you did.
Logged

Offline Al W

  • *****
  • Hero Member
  • Posts: 2535
    • View Profile
Re: Fretwork pedestal table
« Reply #8 on: October 16, 2013, 08:55:34 am »
Excellent work Ray, that one took some time and the results show.  Thanks for letting us have a look.  Very nice.

Al
Logged
Molon Labe

Believe half of what you see, and none of what you hear.

The government is NOT always right, or on your side.

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: Fretwork pedestal table
« Reply #9 on: October 16, 2013, 11:02:37 am »
that's a beautiful bit of craftsmanship. You might take a look at some low power LED lights to keep the heat out of you interior. A hot lamp could over-dry the interior and cause some issues.
Logged
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Offline jerry1939

  • *****
  • Hero Member
  • Posts: 568
  • Iowa - 2 seasons. Winter & road construction.
    • View Profile
Re: Fretwork pedestal table
« Reply #10 on: October 16, 2013, 11:21:20 am »
Awesome.  You have more talent in 1 finger than I have in both hands.

Re: Building a clock.  I built a 42" tall York Minster cathedral, plus a pedestal, for a total height of 6+ feet.  16' string of white Christmas lights inside.

IF I had it to do over again, I would definately attach sheets of stained glass to the insides.

Just my 2 cents worth.

jerry
Logged

Offline RFortier

  • **
  • Jr. Member
  • Posts: 68
    • View Profile
    • Sparetime Scroller
Re: Fretwork pedestal table
« Reply #11 on: October 16, 2013, 01:31:30 pm »
Thank you all for your kind words. I forgot to include any information on the project. It's about 28" tall. The base pieces and top pieces are made of 3/4" oak plywood and edged with walnut banding. The side panels are 1/2" oak plywood and the overlays were done with walnut and maple. I used plexiglass for the top piece just because it was easy to cut and inexpensive.

Thanks again.

Ray F
Logged

Becky

  • Guest
Re: Fretwork pedestal table
« Reply #12 on: October 17, 2013, 11:54:58 pm »
Really nice job there!  Does your pattern designer have a website?  I am not looking for anything specifically like that (at least at this time) but I am always looking for more pattern resources.
Logged

Offline spirithorse

  • *****
  • Hero Member
  • Posts: 925
    • View Profile
Re: Fretwork pedestal table
« Reply #13 on: October 18, 2013, 01:50:58 am »
That's beautiful, Ray!
Thanks for sharing and God Bless! Spirithorse
Logged

Offline RFortier

  • **
  • Jr. Member
  • Posts: 68
    • View Profile
    • Sparetime Scroller
Re: Fretwork pedestal table
« Reply #14 on: October 18, 2013, 12:16:19 pm »
Becky-
 The pattern designer is Dan Wilckens and his website is

www.wilckenswoodworking.net

Ray F
Logged
Pages: [1] 2   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj