« previous next »
Pages: [1]   Go Down

Author Topic: WoodWorking Bench  (Read 1564 times)

king310

  • Guest
WoodWorking Bench
« on: February 01, 2013, 10:28:13 pm »
I made a trade with one of my brothers. I traded him my 3" craftsman belt sander (which I dot not use and he borrowed sometime back)for his woodworking bench that he has never used and just stored junk on it. I will have to clean it up which is ok. It is not a big bench but it will fit into my shop just fine. He told me that our MOM gave it to him for christmas one year which means I will take care of it.When I get it and get it cleaned up I'll post it. ;D
Logged

Offline Al W

  • *****
  • Hero Member
  • Posts: 2535
    • View Profile
Re: WoodWorking Bench
« Reply #1 on: February 02, 2013, 08:59:56 am »
Sounds like a good trade.  Looking forward to the picture.
Logged
Molon Labe

Believe half of what you see, and none of what you hear.

The government is NOT always right, or on your side.

king310

  • Guest
Re: WoodWorking Bench
« Reply #2 on: February 03, 2013, 08:16:44 pm »
OK! I got it cleaned up. My one brother used it for everything but for wood. One vise has thread marks from a bolt that he had clamped. ::) ::). Another spot had burn marks where he soldered something. I was able to sand out most of the burned finish. It is a little narrow, so I will need to make cross braces for the legs
Logged

ShadowB6

  • Guest
Re: WoodWorking Bench
« Reply #3 on: February 03, 2013, 08:36:14 pm »
Looks like you made a good trade trade King. Should get a lot of use out of it.
Logged

Offline Keefie

  • *****
  • Hero Member
  • Posts: 4550
    • View Profile
Re: WoodWorking Bench
« Reply #4 on: February 04, 2013, 09:02:46 am »
great looking bench.
Logged
It's all a case of "Mind over Matter",  The Government don't Mind, and I don't Matter.

Offline Danny

  • *****
  • Hero Member
  • Posts: 1671
    • View Profile
Re: WoodWorking Bench
« Reply #5 on: February 04, 2013, 10:21:58 am »
You made out like a Bandit.  Great looking mid range work bench.  In the pic I see
almost what I would expect to see brand new.  Danny  :+}
Logged
Danny  :+}

Dave W

  • Guest
Re: WoodWorking Bench
« Reply #6 on: February 04, 2013, 12:03:06 pm »
Forget the bench, I would kill for that much workspace!
Logged

king310

  • Guest
Re: WoodWorking Bench
« Reply #7 on: February 04, 2013, 12:45:32 pm »
If you look at the ceiling you will notice my filter system for my furnace.
The furnace has a 3 layer filter system that I put together with a dado blade in a 2x6. The first is a cheap blue filter to take out the bigger dust particles the a merv 5 then a merv 8it takes a lot of the dust out of the air.
Logged

IBMer

  • Guest
Re: WoodWorking Bench
« Reply #8 on: February 04, 2013, 04:04:50 pm »
King, I wouldn't know what to do with ALL that Free space.   My workshop has room for one person to operate the tools and that's about it ;-)   The other day I lost track of my Big Buddy heater, got too close to it and noticed that my sleeve has started to smoke.  Scared me more than hurt me..   I have to be super careful not to bump into anything while in there working.

Logged

Offline cdrover(Clyde)

  • *****
  • Hero Member
  • Posts: 1641
    • View Profile
Re: WoodWorking Bench
« Reply #9 on: February 04, 2013, 06:23:47 pm »
Nice looking shop, thanks for sharing
Logged
What are we here for but to help others. (Author unknown)
Clyde
Pages: [1]   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj