« previous next »
Pages: [1] 2   Go Down

Author Topic: Tilt-O-Scroll  (Read 3615 times)

Offline scotti158

  • ***
  • Full Member
  • Posts: 201
    • View Profile
Tilt-O-Scroll
« on: January 26, 2013, 03:47:58 pm »
 I recently made a scrollsaw bowl. It turned out good and I've had a few request for more of them. The problem is that I hate trying to cut with the table tilted. No problem, I'll just buy a EX21. Whoa, heart says do it, wallet says no way!
   Here is the solution to my dilemma, tilt the table, then tip the saw to get the table level again. A poor mans EX21!
   Check out the picture and tell me what you think. I can tip it 45 degrees both ways.
Logged
Tilt-O-Scroll DW788 Owner/Operater

Offline Al W

  • *****
  • Hero Member
  • Posts: 2535
    • View Profile
Re: Tilt-O-Scroll
« Reply #1 on: January 26, 2013, 03:53:19 pm »
That's using the ole noggin.  Good one!!!
Logged
Molon Labe

Believe half of what you see, and none of what you hear.

The government is NOT always right, or on your side.

king310

  • Guest
Re: Tilt-O-Scroll
« Reply #2 on: January 26, 2013, 04:02:07 pm »
That works for me! You should put a patent on it.
Logged

Offline Rapid Roger

  • *****
  • Hero Member
  • Posts: 1468
  • Hutchinson, Kansas
    • View Profile
Re: Tilt-O-Scroll
« Reply #3 on: January 26, 2013, 04:06:09 pm »
DARN!!!! >:( Why didn't I think of that!  ::) I LOVE your idea!  :)
My saw is on the standard DeWalt stand so, in order to do that I would have to build another stand but, it just might be worth it.
I have made a lot of bowls  and vases over the years and have always struggled with the "table tilt" and never once thought to do what you have done.  :P I really like that.  ;)  
Keep thinking "Outside the lines".

Rog
Logged
An ounce of responsablity is worth 10 pounds of state and fedral laws.

Offline GrayBeard

  • *****
  • Hero Member
  • Posts: 7088
  • My DW 788 sends you HUGZZZZ from Missouri, USA!
    • View Profile
Re: Tilt-O-Scroll
« Reply #4 on: January 26, 2013, 04:07:45 pm »
I think I will use that concept on my "poker table" so the pot will always come my way!

~~~GB~~~
Logged
I never really wanted to grow up....All I wanted was to be able to reach the cookie jar...and play with my DW 788

Offline Billy in Va

  • *****
  • Hero Member
  • Posts: 1002
  • DONT GROW UP ITS A TRAP!!!
    • View Profile
Re: Tilt-O-Scroll
« Reply #5 on: January 26, 2013, 04:13:15 pm »
Good idea GB  But for me it looks lile the table only tilt East- west  and my luck I would  be on the North-South side of the table.
Logged
Common Sense is a flower that does not grow in everyone's garden
Scrollin' - Scrollin' Scrollin' on the River

Offline scotti158

  • ***
  • Full Member
  • Posts: 201
    • View Profile
Re: Tilt-O-Scroll
« Reply #6 on: January 26, 2013, 04:56:09 pm »
Rapid Roger, I also had my saw on the Dewalt stand. My new tilting stand seems to reduce the already low vibration of the DW788. Before if I scrolled at top speed, the saw would be shaking slightly. Now on this heavy stand, top speed is smooth.
Logged
Tilt-O-Scroll DW788 Owner/Operater

king310

  • Guest
Re: Tilt-O-Scroll
« Reply #7 on: January 26, 2013, 05:05:16 pm »
billy just use a left handed floor jack ;D
Logged

Offline Billy in Va

  • *****
  • Hero Member
  • Posts: 1002
  • DONT GROW UP ITS A TRAP!!!
    • View Profile
Re: Tilt-O-Scroll
« Reply #8 on: January 26, 2013, 05:08:45 pm »
King  That ain't the kinda hardware I usually care to the poker table.
Logged
Common Sense is a flower that does not grow in everyone's garden
Scrollin' - Scrollin' Scrollin' on the River

Offline Keefie

  • *****
  • Hero Member
  • Posts: 4550
    • View Profile
Re: Tilt-O-Scroll
« Reply #9 on: January 26, 2013, 06:25:52 pm »
Now thats using the brainbox the way it should be used. excellent thinking - you sure you're not English?? lol
Logged
It's all a case of "Mind over Matter",  The Government don't Mind, and I don't Matter.

Offline jimbo

  • *****
  • Hero Member
  • Posts: 2036
    • View Profile
Re: Tilt-O-Scroll
« Reply #10 on: January 26, 2013, 07:18:28 pm »
Great idea I bet a few members use that one
Jimbo
Logged

Becky

  • Guest
Re: Tilt-O-Scroll
« Reply #11 on: January 26, 2013, 11:34:47 pm »
What a great idea!  At least as long as the saw doesn't fall off.   :o

I applaud your creativity.
Logged

king310

  • Guest
Re: Tilt-O-Scroll
« Reply #12 on: January 26, 2013, 11:52:34 pm »
billy as Bullwinkle said to rocky " nothing up my sleeve"
Logged

Offline newfie

  • *****
  • Hero Member
  • Posts: 5037
  • The Way I Scroll
    • View Profile
    • some of my woodworking
Re: Tilt-O-Scroll
« Reply #13 on: January 27, 2013, 08:34:21 am »
thats a great idea you got there.
Logged


excalibur 21
Every woodworker needs a fireplace

Offline scotti158

  • ***
  • Full Member
  • Posts: 201
    • View Profile
Re: Tilt-O-Scroll
« Reply #14 on: January 27, 2013, 08:43:31 am »
Quote from: Becky on January 26, 2013, 11:34:47 pm
What a great idea!  At least as long as the saw doesn't fall off.   :o

I applaud your creativity.

I have the saw bolted to the table, could saw upside down if I wanted but then the wood would fall off! ;D
Logged
Tilt-O-Scroll DW788 Owner/Operater
Pages: [1] 2   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj