« previous next »
Pages: [1]   Go Down

Author Topic: Am I on the right track part 2  (Read 3006 times)

Offline daveo

  • *****
  • Hero Member
  • Posts: 511
  • DT CRAFTS LINCS UK
    • View Profile
Am I on the right track part 2
« on: May 05, 2013, 12:19:46 pm »
Hi All
well I am finally well enough to get back in the shop so my first piece was one of my own patterns I made with a little tuition from some of you guys ( thanks for that) by no means am i a master but what do you think so far
Dave



Logged

Offline dgman

  • *****
  • Hero Member
  • Posts: 6916
    • View Profile
Re: Am I on the right track part 2
« Reply #1 on: May 05, 2013, 01:20:50 pm »
I think it looks great, nice job!
Logged
Dan In Southern California

Offline Intarsia92

  • *****
  • Hero Member
  • Posts: 1617
    • View Profile
Re: Am I on the right track part 2
« Reply #2 on: May 05, 2013, 02:19:29 pm »
I agree with Dan, It looks just like him. Good job.
Logged
Al

Hegner 20" Polymax

Offline Dan26

  • *****
  • Hero Member
  • Posts: 698
  • South of Milford, Ohio
    • View Profile
Re: Am I on the right track part 2
« Reply #3 on: May 05, 2013, 07:35:09 pm »
Looking good.
Logged
Dan (South of Milford, Ohio)

Courage - the ability to confront fear, pain, danger, uncertainty, or intimidation.

Offline Marcellarius

  • *****
  • Hero Member
  • Posts: 6135
  • Scrolling each day, keeps the doctor away
    • View Profile
    • Some of my work
Re: Am I on the right track part 2
« Reply #4 on: May 06, 2013, 01:44:57 am »
looks really nice. keep on going!
Logged
Marcel

sometimes I make designer firewood....

king310

  • Guest
Re: Am I on the right track part 2
« Reply #5 on: May 06, 2013, 09:00:35 pm »
daveo that is a great piece of work. Is that of you.......
Logged

Offline EIEIO

  • *****
  • Hero Member
  • Posts: 2147
  • Be Prepared.
    • View Profile
    • RMHayes, LLC
Re: Am I on the right track part 2
« Reply #6 on: May 06, 2013, 09:05:45 pm »
Excellent - especially well done around the hair (that's hard to get simple enough to cut).
Logged
EX-21 arrived 2-1-2013!
Porter-Cable PCB370SS in the corner
Lancaster Ohio
Ray Hayes - RMHayes@RMHayes.US
www.RMHayes.US

Offline mickey357

  • *****
  • Hero Member
  • Posts: 692
    • View Profile
Re: Am I on the right track part 2
« Reply #7 on: May 07, 2013, 12:22:50 am »
 Great !!!! You hit that out of the ball park. Very nice.
Logged

Offline Tomsunnu

  • *****
  • Hero Member
  • Posts: 1608
    • View Profile
Re: Am I on the right track part 2
« Reply #8 on: May 07, 2013, 04:16:07 am »
Dave,
Very nicely done. Keep practicing :)

Mahendra
Logged
mahendra

Offline daveo

  • *****
  • Hero Member
  • Posts: 511
  • DT CRAFTS LINCS UK
    • View Profile
Re: Am I on the right track part 2
« Reply #9 on: May 07, 2013, 11:38:11 am »
thank you all for the encouraging comments, the good side is that this whole thing is already going commercial, just hope I can satisfy the customers.
king310 nnoits not me, I'm ugly why do you thing I don'y use an avatar
Dave
Logged

Old Crow

  • Guest
Re: Am I on the right track part 2
« Reply #10 on: May 07, 2013, 12:05:09 pm »
Well done, Dave. You are definitely on the right track!
Don R
Logged

Offline Keefie

  • *****
  • Hero Member
  • Posts: 4550
    • View Profile
Re: Am I on the right track part 2
« Reply #11 on: May 08, 2013, 11:53:59 am »
Great cutting and brilliant pattern - you're definately on the right track.
Logged
It's all a case of "Mind over Matter",  The Government don't Mind, and I don't Matter.

ShadowB6

  • Guest
Re: Am I on the right track part 2
« Reply #12 on: May 08, 2013, 07:04:23 pm »
A great job Dave. I started a few months ago doing up portraits and to me, it's much harder than it looks. So again, GREAT JOB.

Mike
Logged

Offline wombatie

  • *****
  • Hero Member
  • Posts: 5557
  • Victoria Australia
    • View Profile
Re: Am I on the right track part 2
« Reply #13 on: May 09, 2013, 02:05:23 am »
Excellent.

Marg
Logged
MARG

No one notices what I do until I'm not here to do it............
Pages: [1]   Go Up
« previous next »
 

SMF

Teknoromi

SMF Links

  1. XHTML
  2. RSS
  3. WAP2
  4. Theme by snrj