1
Pattern Requests. / Re: Minnesota Vikings Scroll Saw Pattern
« on: July 11, 2022, 01:26:23 pm »
try this
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2
General Scroll Saw Talk / Re: Merry Christmas!
« on: December 25, 2020, 11:53:40 am »
Merry different and a Happy New what ever whatever we get
3
Ask Steve a question. / Re: cnc
« on: December 04, 2020, 12:33:06 pm »
hi
dont use the inkscape extension unless you know a lot about g code
now I dont use fusion I use artcam which is also an autodesk product so assume they are similar
you need to create a solid black image like say the attached letter b
save it as jpg or png
then open it in fusion, from there you will convert it to a vector then create 2 toolpaths one for the inner cut and one for the outer
and away you go
Dave
dont use the inkscape extension unless you know a lot about g code
now I dont use fusion I use artcam which is also an autodesk product so assume they are similar
you need to create a solid black image like say the attached letter b
save it as jpg or png
then open it in fusion, from there you will convert it to a vector then create 2 toolpaths one for the inner cut and one for the outer
and away you go
Dave
4
General Scroll Saw Talk / Re: Font use on Happy Halloween pattern
« on: October 21, 2020, 10:15:15 am »
hi
its HOBO
its HOBO
5
Pattern Requests. / Re: I have a family photo I want to make into a pattern
« on: June 09, 2020, 12:20:46 pm »
hi e mail me the pic
info.dtcrats@gmail.com
Dave
info.dtcrats@gmail.com
Dave
6
General Scroll Saw Talk / Re: If my Hegner motor spins, does that mean it’s OK?
« on: May 09, 2020, 11:20:49 am »
HI
sure they could but would advise getting the capacitor from hegner first rather than risk using a similar item
sure they could but would advise getting the capacitor from hegner first rather than risk using a similar item
7
General Scroll Saw Talk / Re: If my Hegner motor spins, does that mean it’s OK?
« on: May 08, 2020, 11:19:38 am »
hi the start capacitor is shot
they need to be fully charged to be able to give that initial kick of power when under load (with the belt attached)
the chances are that if you could give the pulleys a spin by hand whilst the motor is humming it would start and run until next switch off
be very careful if you try this its a bit nasty if you get those pinkies in the belt
so new capacitor first if that fails then it could be the windings burnt out but that is rare
Dave
they need to be fully charged to be able to give that initial kick of power when under load (with the belt attached)
the chances are that if you could give the pulleys a spin by hand whilst the motor is humming it would start and run until next switch off
be very careful if you try this its a bit nasty if you get those pinkies in the belt
so new capacitor first if that fails then it could be the windings burnt out but that is rare
Dave
8
Introduce Yourself. / Re: Blade Clamps
« on: November 17, 2019, 09:53:52 am »
hi these will work
https://www.axminster.co.uk/axminster-blade-clamp-for-awvfs-scroll-saw-400124
Dave
https://www.axminster.co.uk/axminster-blade-clamp-for-awvfs-scroll-saw-400124
Dave
10
Introduce Yourself. / Re: Hi From Lincolnshire
« on: August 17, 2019, 01:52:16 pm »
HI CLIVE
I am in mablethorpe Lincs where are you
Dave
I am in mablethorpe Lincs where are you
Dave
11
Ask Steve a question. / Re: Email
« on: March 08, 2019, 12:11:25 pm »Gmail kicking you out? Never heard of such a thing.that was my first thought, but thought better of asking, does seem strange
12
Ask Steve a question. / Re: Email
« on: March 07, 2019, 12:54:07 pm »
Profile>account settings change address confirm current password click change profile
13
General Scroll Saw Talk / Re: Very small issue
« on: December 30, 2018, 09:45:28 am »
Rick
when you say FD 2/0 reverse is that the UR, if so thats the problem every third tooth is reversed and you will have a reverse tooth clipping the face of the puzzle
I use Niqua fix reverse in that only a few teeth are reversed at the bottom of the blade and are similar in configuration to the ones Norm is using
Dave
when you say FD 2/0 reverse is that the UR, if so thats the problem every third tooth is reversed and you will have a reverse tooth clipping the face of the puzzle
I use Niqua fix reverse in that only a few teeth are reversed at the bottom of the blade and are similar in configuration to the ones Norm is using
Dave
14
General Scroll Saw Talk / Re: Wobbly blade clamp
« on: November 03, 2018, 11:13:45 am »I would like to thank everyone for their help. I went to or called 4 different DeWalt service outlets here. None of them had the "short sleeve" part in stock and it would have to be ordered in. Estimated time anywhere from 5 days to 3 weeks. Each sleeve was aproximately $10. I was looking to replace the 4 on the clamps. Decision time - I was going to put the Pegas clamps on my Christmas wish list. It is not on the list anymore, just ordered them this afternoon.BarbShould be here in a week!! Yes the Pegas clamps are twice the price of the sleeves, but I am sure it will be more than worth it. Can't wait!!! Hope Canada Post doesn't actually go on strike!
just fitting new clamps is not going to rectify the bearing problem
here are the sleeves
https://www.ereplacementparts.com/short-sleeve-p-67068.html
Dave
15
Introduce Yourself. / Re: Hi , It's me again !!
« on: February 20, 2018, 11:45:30 am »
hi
yes I have and just looking it is just 4 years ago
check your e mails
Dave
yes I have and just looking it is just 4 years ago
check your e mails
Dave
