Messages

1

General Scroll Saw Talk / Re: Blade feeding

« on: November 04, 2016, 08:38:40 am »

Learned scroll on my own.  I have a EX 21 and seen very fast that it is easier to see hole on top of board than looking under it.  I learned to FEEL were the blade needs to go without looking.  Takes about 4 sec to go from hole to hole.  If your hole in board isn't lined up with hole in table you will bend blade but don't drop arm put in slow till you are sure.  On the village site the poll results are much closer on top vs bottom than here for some reason.  Think if you are a long time scroller you had to start out on saws that only bottom feed at the time.  Now the new ones give a option.

2

Brag Forum / Pig Clock

« on: June 13, 2016, 02:57:56 pm »

Woman wanted a pig clock for her son.  Looked at Steve's patterns and found a pig and used the resize program to make bigger.  Turned out fine.

3

Pattern Requests. / Dog Clock

« on: May 08, 2016, 04:28:40 pm »

The "kitty clock" that Steve just posted is nice an simple would you make one in the same line as a dog?

4

Tutorials, Techniques and Tips / Re: Top or bottom feed

« on: June 04, 2015, 10:05:37 pm »

Have had my EX for 5 years and set the back knob one time never moves.  Lower arm one hand put blade into hole with other and as it starts into the hole move hand to bottom clamp to guide it.  I can change holes in about 3 sec after you get use to it.  Just my 2 cents worth.  Also agree you should check with Ray sounds like you got a bad table from factory.  My table is flat all the way around.

5

General Scroll Saw Talk / colored veneer

« on: January 13, 2015, 02:18:46 pm »

Were is a good place to buy dryed colored veneer?  Thanks

6

Computer questions / Re: posting pictures

« on: January 24, 2012, 01:09:15 pm »

Thanks Hamilton!  Sometimes the mind doesn't work to good.  What I was doing was trying to find the address bar on the Picasa web page.  Picasa page was covering up my address bar for AOL and as soon as I draged the page down I could see it (address bar).   Thanks again and for putting up with my old man brain.

7

Computer questions / Re: posting pictures

« on: January 23, 2012, 05:14:02 pm »

I know Steve in one of his videos said he would make another video showing how to go through Picasa but I can't find it either.  I tryed finding the address bar in the Picasa program you told me about but dumb me I can't find it.  Just about to give up lol.

8

Computer questions / Re: posting pictures

« on: January 23, 2012, 01:03:28 pm »

I have my pictures on the Picasa web site.  But I can't figure out how to "link to the photos" to get the picture here on this forum.  Can you help me just a bit more?  LOL  Thanks

9

Computer questions / Re: posting pictures

« on: January 23, 2012, 06:57:42 am »

Thanks Russ, but I was wanting to be able to post a picture with a message.  Steve said you have to upload your picture to a web site an than download to this site somehow because of the size limit.  I see the galley you was taking about.  I want to give the person that made the pattern for me a pat on the back an show how it turned out.  Thanks

10

Computer questions / posting pictures

« on: January 22, 2012, 01:38:25 pm »

I watched Steve's video on uploading pictures to the forum.  But I can't find his other video telling how to upload a file bigger than 124 kb.  Were is the video or how do I do it?   Thanks

11

Pattern Requests. / Re: 1997 corvette

« on: January 04, 2012, 03:12:52 pm »

Thanks for the corvette pattern, very nice!  I am going to cut it for my brother.

12

Pattern Requests. / 1997 corvette

« on: January 03, 2012, 01:22:59 pm »

Would any one have a pattern of a 1997 corvette or can make one?  Thanks in advance!