946
The Coffee Shop / Re: Be VERY careful what you pray for....you may get it!
« on: July 24, 2013, 05:57:39 pm »
lol, now that one is going the rounds of my address list 
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
947
Brag Forum / Re: Jesus Plaque
« on: July 24, 2013, 05:55:46 pm »
Great job dustin, couldn't see the video link this time lol.
Keefie.
Keefie.
948
Brag Forum / Re: Follow up to my "By Royal Appointment" post.
« on: July 24, 2013, 01:44:57 pm »
Not a hope Rob, I can hardly even walk at the minute after my op yesterday - I'm damn sure they didn't put any slow release anaesthetic in my knee this time. must be due to cutbacks lol
950
Brag Forum / Re: Williamette Clock
« on: July 24, 2013, 08:35:03 am »
That is a truly AWESOME piece of work, your father will love it.
Keefie
Keefie
951
Brag Forum / Re: welcome sign
« on: July 24, 2013, 08:31:35 am »
Very nice clean cuts, an axcellent piece of work.
Keefie.
Keefie.
952
Brag Forum / Re: Baby Cross
« on: July 24, 2013, 08:29:13 am »
Excellent work, very nice cutting. (I think it is a Sue May pattern - I have some similar patterns of hers.)
953
Brag Forum / Re: The kid I can't figure out
« on: July 24, 2013, 08:27:14 am »
Very nice work, from a good pattern.
Keith
Keith
954
Brag Forum / Re: My tribute to Dermott O'Toole
« on: July 24, 2013, 08:25:14 am »
Excellent work Marg, and a very fitting tribute for a kind man.
Keefie.
Keefie.
955
Brag Forum / Follow up to my "By Royal Appointment" post.
« on: July 24, 2013, 08:21:45 am »
After my By Royal Appointment post, I thought I would post the pictures of The Duchess of Cornwall being presented the bowl by the crew of the Cornwall Air Ambulance. (I made the centre inlay and another turner made the bowl) Thanks go again to Paul (Grampa) for the brilliant pattern.
Keefie
Keefie
956
Introduce Yourself. / Re: Hello From Halifax, Nova Scotia, Canada
« on: July 21, 2013, 04:26:36 pm »
Hi Jim, welcome to the forum, I'm Keith from Cornwall U.K.
957
General Scroll Saw Talk / Re: Let's Have a good old fashion debate !
« on: July 21, 2013, 04:17:41 pm »
"I'm not thrilled with the dust removal ports (a special option). They seem to clog when bigger cut-out pieces fall into them."
Ray, I had this problem, I made a U shaped plate from 6mm ply and forred it between the extractor port and the table to give a 6mm bigger opening for dust and debris to enter, this seemes to have solved that problem. I have not had your problem of the dust port getting in the way of top feeding as I always top feed. The dust port does get in the way slightly when pivoting the top arm fully to the left, however if I need to tilt it that far, I just tilt it in the other direction then cut in the opposite direction too - problem solved.
All in all I think the Excalibur EX21 is excellent value for money and I have yet to hear one bad report about the excellent back up service recieved from Ray @ Seyco.
Keefie.
Ray, I had this problem, I made a U shaped plate from 6mm ply and forred it between the extractor port and the table to give a 6mm bigger opening for dust and debris to enter, this seemes to have solved that problem. I have not had your problem of the dust port getting in the way of top feeding as I always top feed. The dust port does get in the way slightly when pivoting the top arm fully to the left, however if I need to tilt it that far, I just tilt it in the other direction then cut in the opposite direction too - problem solved.
All in all I think the Excalibur EX21 is excellent value for money and I have yet to hear one bad report about the excellent back up service recieved from Ray @ Seyco.
Keefie.
958
The Coffee Shop / Re: Quite
« on: July 21, 2013, 04:03:23 pm »
We could all meet up for a barbie on the beach!!!!
Keefie.
Keefie.
959
Brag Forum / Re: mesquite slabs
« on: July 21, 2013, 04:02:16 pm »
Awesome work, love the natural edges.
Keith
Keith
960
Brag Forum / Re: Salt & Pepper Shakers
« on: July 21, 2013, 04:00:41 pm »
nice work Dustin, and yet another good video too.
Keith.
Keith.
