886
Pattern Requests. / Re: Pic. Frames
« on: February 22, 2011, 07:02:22 pm »
That is a kewl frame. If Johnny isn't interested I am...<grin>
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
887
Computer questions / Re: New FireFox version 4 is just days away!
« on: February 22, 2011, 01:10:02 am »
Is this a good thing?
888
Pattern Requests. / Re: Pic. Frames
« on: February 21, 2011, 08:05:46 pm »
That is a very broad request. Can you be more specific in what you looking for?
889
General Scroll Saw Talk / Re: Blotchy stain help..
« on: February 21, 2011, 03:56:05 pm »
Roger is correct I'll just add I sand the end grain to one grit higher than the long grain. So if I do the long grain to 220 I'll go to 240 or even 320 on the end grain.
890
Brag Forum / Re: Sweethearts
« on: February 20, 2011, 12:15:37 pm »
Really like the contrasting woods. Nicely done.
892
Computer questions / Re: What has happened to the site?
« on: February 20, 2011, 11:08:32 am »
Thanks for letting us know Steve.
GB, I have this flippin image in my brain now of these little fellas marching along whistlin a tune like "Whistle while you work"....LOL
GB, I have this flippin image in my brain now of these little fellas marching along whistlin a tune like "Whistle while you work"....LOL
893
General Scroll Saw Talk / Re: Hegner Scroll Saw
« on: February 20, 2011, 11:05:56 am »
I've had my dewalt for almost 12 years. Love my saw but it si showing signs of wear and recently I stripped out the thumb screw for the blade clamp. I replaced both the top and bottom blade clamps and now I have very noticeable back and forth motion on the blade.
I decided that this is unacceptable and can not be fixed easily so I have just ordered a Excalibur 21 inch saw from Seyco. I've heard very good things about it and could not myself justify a Hegner or Hawk. I do a lot of cutting as I have a local weekend Saturday Mkt all summer (22 weeks), local craft shows and a relatively busy website. So I required a reliable saw and after about 2 months of research and soul searching decided the Seyco saw was for me.
I decided that this is unacceptable and can not be fixed easily so I have just ordered a Excalibur 21 inch saw from Seyco. I've heard very good things about it and could not myself justify a Hegner or Hawk. I do a lot of cutting as I have a local weekend Saturday Mkt all summer (22 weeks), local craft shows and a relatively busy website. So I required a reliable saw and after about 2 months of research and soul searching decided the Seyco saw was for me.
894
General Scroll Saw Talk / Re: How would you finish this project?
« on: February 20, 2011, 12:39:50 am »
Actually I agree with DGman except on one point. Mineral spirits is safe in plastic. Go to any hardware store and you can buy a quart in a plastic container.
895
Computer questions / Re: What has happened to the site?
« on: February 20, 2011, 12:37:29 am »
Oh good I've tried the tricks to fix my resolution etc but it is just this site. I'm glad it is not just me. Thanks for the responses.
896
Computer questions / What has happened to the site?
« on: February 19, 2011, 09:50:09 pm »
When i logged in a few minutes ago I noticed there is a new look to the site.
There is about a 3" gray border on the left and right side of the forum now.
I did not change anything as far as setting s go and the font size is minuscule. What happened. Nothing else is wonky on the net for me just here.
There is about a 3" gray border on the left and right side of the forum now.
I did not change anything as far as setting s go and the font size is minuscule. What happened. Nothing else is wonky on the net for me just here.
897
Brag Forum / Re: Dick Boelman's The Elegant Cross
« on: February 19, 2011, 08:11:55 pm »
Bill that is super.
Steve you can do it. Just one cut at a time.
Steve you can do it. Just one cut at a time.
898
General Scroll Saw Talk / Re: I did it...I did It...
« on: February 19, 2011, 08:10:39 pm »
I will report back. Judy i promise. I'm leaving my 788 as a backup saw.
900
Brag Forum / Re: Cross for friends' wife
« on: February 19, 2011, 01:10:29 pm »
Nice job and I'm sure you warmed the cockles for Paul in completing it so quickly!
