61
Brag Forum / Re: New Bank design
« on: March 19, 2018, 10:03:53 am »
Good job. I like it.
Larry
Larry
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
62
Pattern Requests. / Re: Billy Graham
« on: March 07, 2018, 10:41:02 am »
Steve posted a picture of Billy Graham pattern by Charles Dearing on Feb 24 Newsletter and Daily Blog.
This was to let us know that Bear Woods has several Billy Graham patterns made by Charles Dearing.
The link that was posted is the same link Paul shows above.
Larry
This was to let us know that Bear Woods has several Billy Graham patterns made by Charles Dearing.
The link that was posted is the same link Paul shows above.
Larry
63
General Scroll Saw Talk / Re: Scrolling on Cherry Wood
« on: February 16, 2018, 10:53:13 pm »
I cover the wood with painter's tape or clear shelf liner then glue the pattern on. I also slow the blade speed down a bit.
Larry
Larry
64
General Scroll Saw Talk / Re: Foot pedal
« on: February 15, 2018, 10:15:18 am »
I use the HF model as well. Believe a foot pedal simply transfers the saw's on/off switch from the saw to the floor.
Larry
Larry
65
General Scroll Saw Talk / Re: Bear woods and steve good contests
« on: February 06, 2018, 08:12:14 pm »
We do not have to make the draw to be a winner.
Dios bendiga! Larry
Dios bendiga! Larry
66
General Scroll Saw Talk / Re: Bear woods and steve good contests
« on: February 06, 2018, 10:28:49 am »67
Ask Steve a question. / Re: DW 788 TABLE WAXING
« on: January 29, 2018, 12:53:46 pm »
Johnson Paste Wax here, also.
Larry
Larry
68
Ask Steve a question. / Re: Steve's what the heck is it? project
« on: January 25, 2018, 07:00:32 pm »
Blade square to table checker. When each bolt head touches blade circuit is complete and the led comes on. Level bolt heads with the square and give it the ole smoke test.
Larry
Larry
69
General Scroll Saw Talk / EX-21 at Home Dept
« on: January 25, 2018, 10:21:12 am »
I posted this link at The Patriotic Woodworker on Dec 16, 2017 about the EX 21 now available at Home Depot.
https://www.homedepot.com/p/Excalibur-120-Volt-21-in-Tilting-Head-Scroll-Saw-with-Stand-and-Foot-Switch-EX-21K/205414436?cm_mmc=Shopping|THD|G|0|G-BASE-PLA-AllProducts|&gclid=EAIaIQobChMI08SanO2P2AIV1o2zCh2Dtgz-EAQYAiABEgIdG_D_BwE&gclsrc=aw.ds&dclid=CM-Mn6Ptj9gCFVGtTwod5moDig
Larry
https://www.homedepot.com/p/Excalibur-120-Volt-21-in-Tilting-Head-Scroll-Saw-with-Stand-and-Foot-Switch-EX-21K/205414436?cm_mmc=Shopping|THD|G|0|G-BASE-PLA-AllProducts|&gclid=EAIaIQobChMI08SanO2P2AIV1o2zCh2Dtgz-EAQYAiABEgIdG_D_BwE&gclsrc=aw.ds&dclid=CM-Mn6Ptj9gCFVGtTwod5moDig
Larry
70
The Coffee Shop / Re: Doctor advises pregnant women to walk every day
« on: January 20, 2018, 11:23:06 am »
One of the couples decided they would walk 5 miles a day. Two weeks later they called the Dr's office to cancel their appoint for the next day. "Why do you need to cancel?, they were asked. "Well, we are 70 miles from home and can't walk back by tomorrow".
Larry
Larry
71
Ask Steve a question. / Re: Dewalt DW788 foot pedal
« on: January 18, 2018, 10:42:39 am »
Most of the speed changing problems I have read about are caused by a faulty variable speed control switch. Most foot switches are just an extension of the on/off switch for the saw and all they do is cut the saw on and off. They do not control speed. However, you state the speed change only happens when you are using the foot switch. Have you tried it for an extended time without the foot switch? Several hours or so? (I had to replace my foot switch and while I was waiting on the new one, I would press the spot on the floor where the switch normally set and after a few times and then remember the saw switch.)
Larry
Larry
72
General Scroll Saw Talk / Re: SCROLL BEACH ITALIC FONT MISSING
« on: January 03, 2018, 06:19:34 pm »73
Introduce Yourself. / Re: Hello From Guam
« on: January 02, 2018, 09:39:54 am »
Welcome George. Glad to have you on board. Thank you for your service. I am retired Army.
Larry
Larry
74
The Coffee Shop / Re: Smiling Faces
« on: December 22, 2017, 10:57:24 am »
Merry Christmas Bill and others. They say "a picture is worth a thousand words". I believe a smile is worth a million bucks.
Larry
Larry
75
Brag Forum / Re: Inlay on box lids.
« on: December 14, 2017, 09:51:31 am »
Nice work, Jim. I grew up calling bois d'arc horse apple tree. Scrolled some for compound Christmas ornament. Was getting smoke and black hot chips when the going got tough.
Larry
Larry
