46
The Coffee Shop / Re: 20th
« on: October 19, 2010, 05:16:00 am »
Congrats, Jimbo!
Paul
Paul
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
47
General Scroll Saw Talk / Re: Anyone selling shelves at craftshows?
« on: October 19, 2010, 05:12:40 am »
Thank you for your answer, Bill! I will make up a couple and give it a try!
Paul
Paul
48
General Scroll Saw Talk / Anyone selling shelves at craftshows?
« on: October 17, 2010, 09:12:20 am »
I broke down and bought a new Ryobi router/table at Home Depot. Really works great! Up and running in 45 minutes. Was thinking of making some shelves. Something like Wildwood designs, or Scroller, LTD. Was wondering if they are "movers" or not worth the time/effort/cost. Anyone? Thanks!
Paul
Paul
49
General Scroll Saw Talk / Re: Ethical Delima
« on: October 13, 2010, 08:13:55 am »
That would have been my solution, Terry. Nice blogspot, also.
Paul
Paul
50
General Scroll Saw Talk / Re: I'm thinking about getting a router
« on: October 01, 2010, 05:14:27 am »
I built and used the Dremel table mentioned. It's okay, but don't expect to use it a lot. The bits dull quickly.
Because of my budget, I will be looking on Craigslist for a router/table set-up. I have seen some extremely great deals out there. I recently bought a Craftsman 12" bandsaw, with 4 assorted new blades for $25!
Because of my budget, I will be looking on Craigslist for a router/table set-up. I have seen some extremely great deals out there. I recently bought a Craftsman 12" bandsaw, with 4 assorted new blades for $25!
51
Introduce Yourself. / Re: hello
« on: August 24, 2010, 06:30:00 am »
Hi Bill! Is that a V-dub trike? I sure would like to have one again! Ride safe! This site has a lot of great people on it. Any questions about scrolling, don't hesitate to ask!
Paul
Paul
52
The Coffee Shop / Re: Image Shack vs. PhotoBucket???
« on: August 18, 2010, 07:51:50 am »
I really like flickr.com Free, very easy to load. Owned by yahoo, so also a secure site.
Paul
Paul
53
The Coffee Shop / Re: It is HOT!!!!
« on: August 04, 2010, 05:53:57 am »
Going to be in the mid-90's here in the Akron,Oh. area today. Arrrrggghhh! Still beats snow!
Paul
Paul
54
General Scroll Saw Talk / Re: Forum Speed Issues.
« on: August 04, 2010, 05:40:21 am »
Thanks, Steve! So far, much faster!
Paul
Paul
55
General Scroll Saw Talk / Re: Snowman--A Schwibbogen
« on: August 01, 2010, 06:39:53 am »
Great work, and great idea, Chase!
I do all my sanding before I do the cut-outs. Seriously, so much easier to use the palm sander, finishing with a 220grit. Seems like less fuzzies to contend with.
Paul
I do all my sanding before I do the cut-outs. Seriously, so much easier to use the palm sander, finishing with a 220grit. Seems like less fuzzies to contend with.
Paul
56
General Scroll Saw Talk / Re: 3 FREE patterns July 31, 2010
« on: August 01, 2010, 06:32:14 am »
Thank you, Charlie! Much appreciated!
Paul
Paul
57
General Scroll Saw Talk / Re: Craig's List.....
« on: July 10, 2010, 06:03:46 am »
I have been using that Craftsman saaw for nearly 3 years. Lots of hours on it. Except for the on/off switch going bad, not one problem with it. Great entry-level saw. When it goes out, I will most likely move up to a Dewalt.
Paul
Paul
58
General Scroll Saw Talk / Re: Free 4 All Patterns
« on: June 29, 2010, 04:43:21 am »
Thanks for the update, Cherie! I haven't been able to log on there for quite a while!
Paul
Paul
59
General Scroll Saw Talk / Re: I need some information on a scroll saw . . .
« on: June 15, 2010, 06:40:56 am »
I have been using the Craftsman version for over 2 1/2 years. No problems, except for the on/off switch. I eliminated the switch, and use a foot switch. Also tell him to scrap the hold down foot. Use the screw from that to replace the lower blade clamp screw. Much easier blade changes. Same size thread, but larger grip area. Leave off the cover below the table. Also much easier blade changing, and cleaning. And, on my flickr pics, I have a couple of pics of my own zero clearance insert. Works excellant for me. Replaces the plastic insert. Hope this helps!
Paul
Paul
60
The Coffee Shop / Re: day 1 Denton Texas
« on: June 13, 2010, 03:30:55 am »
Thank you for all the pics, Cherie! Really do appreciate it!
Paul
Paul
