271
General Scroll Saw Talk / Re: Magnifier Lamps, give us a report!
« on: April 26, 2012, 02:05:01 pm »
Judy what will you want for yours?
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
272
General Scroll Saw Talk / Re: Magnifier Lamps, give us a report!
« on: April 24, 2012, 08:36:43 am »
I have one like you Gabby and it is Ok, but I find the cantilever is awkward for scrolling.
273
General Scroll Saw Talk / Re: Top Feeding blades on Inside Cuts
« on: April 09, 2012, 09:11:59 pm »
My EX-21 does.
274
The Coffee Shop / Re: Gun Control
« on: April 06, 2012, 08:37:46 pm »
Gun control is all about hitting your target.
275
General Scroll Saw Talk / Re: Watching Videos
« on: April 05, 2012, 04:27:28 pm »
Your internet connection is too slow.
276
General Scroll Saw Talk / Re: Oven Pulls
« on: March 27, 2012, 03:29:15 pm »
Only problem is I have never seen a spade bit that small.
277
General Scroll Saw Talk / Re: Oven Pulls
« on: March 26, 2012, 02:04:16 pm »
I could use a 3/4" wide board and have room left over. I used 1/2" for a small electric counter top oven the wife uses often since there is just the two of us in the house most of the time.
278
General Scroll Saw Talk / Oven Pulls
« on: March 26, 2012, 11:53:37 am »
What kind of wood are most of you using for the oven pulls? I just made one with 1/2" poplar and I get too much break out when the drill bit comes through and that causes problems on the small cut outs. Thinking about trying some 3/4" red oak, maybe some good quality pine, the ones I want to make for wife and DIL's I will want something that looks real nice.
279
Brag Forum / Re: latest projects
« on: March 24, 2012, 07:05:37 pm »
Nice, but what is the BLO that is mixed with Mineral Spirits.
280
Ask Steve a question. / Steve's patterns
« on: March 24, 2012, 04:50:35 pm »
How do you access Steve's patterns? I found it before by stumbling upon them before but cannot find them again.
281
General Scroll Saw Talk / Re: Baltic Birch Plywood Source
« on: March 23, 2012, 08:26:56 pm »
I have bought some 1/8" ply at Hobby Lobby, the quality is not the greatest but fair. Don't remember the price.
282
General Scroll Saw Talk / Re: Solved my problem
« on: March 23, 2012, 12:42:59 pm »
What kind of saw do you have?
283
General Scroll Saw Talk / Re: How do you apply your pattern?
« on: March 20, 2012, 09:28:10 am »
Blue painters tape then 3M #77 spray adhesive then clear packing tape over the pattern to prevent smearing and lube the blade.
284
General Scroll Saw Talk / Re: Been extremely busy
« on: March 20, 2012, 09:26:50 am »
On your whirligigs do you buy your hardware or make your own? The kits are kind of expensive to make more than one, Ok if you only make one for your self.
285
General Scroll Saw Talk / Re: Scroll Saw Table Scratches
« on: March 16, 2012, 08:45:41 am »
maritimer, Let us know what they say and do.
