2011
The Coffee Shop / Guns
« on: January 10, 2013, 05:49:10 pm »
I thought you might like this ,I found it on facebook
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
2012
Pattern Requests. / Re: OMG! I made a pattern!
« on: January 10, 2013, 05:38:45 pm »
Nice one GB, I pinched a copy too as my son lives in Northern Ireland so I'll make him a smaller set as coasters.
2013
The Coffee Shop / Re: This is the big one
« on: January 10, 2013, 03:54:03 pm »
good luck Clyde, hope you don't get too much of the white stuff
2014
The Coffee Shop / The best home security system
« on: January 10, 2013, 01:16:59 pm »
I saw this and had to share it with you....
2015
The Coffee Shop / Re: Can Cold Water Get Dishes Clean?
« on: January 10, 2013, 01:04:44 pm »
lol 
2017
General Scroll Saw Talk / Re: Best Types of Wood to Use
« on: January 10, 2013, 04:48:52 am »
Usually it is a fairly plain wood with a little graining on it, but I think I read somewhere you can get it in the USA with with oak, cherry ,maple and other woods on the top surface (like a veneer), but here in the UK we are limited to plain Birch Ply. I have attatched a pic of the Cornwall Air Ambulance made from plain Birch Ply and finished with Blo/ thinners and 2 coats of lacquer to show you what it looks like. (if you finish it using a stain it brings out the marking more)
2018
General Scroll Saw Talk / Re: Best Types of Wood to Use
« on: January 10, 2013, 04:29:37 am »
Plywood works extreemly well on the scrollsaw, I use it 90% of the time. But you must get Birch ply (Baltic Birch Ply in USA) as it is best quality wood right through the layers with no voids (spaces in the middle). I cut it with Flying Dutchman Ultra Reverse blades usually a #1 or #3 size blade, it leaves it with an almost perfect finish with little or no sanding required on the cuts. (I always sand both front and back surfaces before cutting as this means not much sanding after its cut)
Hope this helps.
Keith.
Hope this helps.
Keith.
2019
The Coffee Shop / Re: Wake Up Call, Who is Missing?
« on: January 10, 2013, 03:08:16 am »
Big Pete hasn't been on for a while, but I sent him an email the other day to check he was ok. He has had some personal problems so hasn't been cutting anything, but he is well and hopes to get back soon.
2020
Brag Forum / Re: A few 3d critters cut with my dewalt 788
« on: January 10, 2013, 02:49:54 am »
Wow, thatts pretty small, well cut too.
2021
Pattern Requests. / Re: help with pattern need please
« on: January 09, 2013, 06:28:33 pm »
Very nice Don, thanks for helping out.
2022
The Coffee Shop / Re: The Haircut
« on: January 09, 2013, 06:26:12 pm »
Billy, If I found a country that wants them I would give them all of ours before you got the chance to dump all yours lol 
2023
The Coffee Shop / Re: The Resurrection
« on: January 09, 2013, 06:22:24 pm »
I agree Billy, just blew mine everywhere lol
2025
Pattern Requests. / Re: New Grandson pattern request
« on: January 09, 2013, 03:52:45 pm »
Great job Mahendra,
