Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jimbo

Pages: 1 ... 125 126 [127] 128 129 ... 136
1891
Ask Steve a question. / Re: category for supplies?
« on: June 05, 2010, 05:59:39 pm »
A great idea, perhaps put these in the coffee shop dept.
Jimbo

1892
Ask Steve a question. / Re: Birthdays
« on: June 05, 2010, 05:57:14 pm »
Hi Cloetpatrick
My wife is worse off than me so I don't say too much about my problems, she has scoliosis of the spine, and on top of that she had to have a complete knee replacment last year, the knee is great but her back is not has to take pills all the time for pain.
No sypathy is required as she seem to cope well with all the pain, both our engine depts. work fine so that is the main thing
Jimbo

1893
The Coffee Shop / Re: Spell Checking
« on: June 05, 2010, 05:47:25 pm »
different countries have different ways of spelling words and I aint changing, if you you can't understand my spelling ask me and I will spell it out for you
Have a happy day
Jimbo
and it is still 10c

1894
The Coffee Shop / Re: On Line
« on: June 05, 2010, 05:42:48 pm »
yeh look at my new posting
Jimbo

1895
The Coffee Shop / Re: What is a 710?
« on: June 05, 2010, 05:40:17 pm »
sounds like you were in panic mode Russ
Jimbo

1896
The Coffee Shop / Paradise
« on: June 05, 2010, 05:37:53 pm »
another day in paradise, pouring with rain and a massive 10c
Jimbo

1897
The Coffee Shop / Re: HillBilly Mirror!
« on: June 05, 2010, 05:36:28 pm »
mirror mirror on the wall
Jimbo

1898
The Coffee Shop / Re: They are in and connected!
« on: June 05, 2010, 05:34:43 pm »
good one Gray Beards
Jimbo

1899
General Scroll Saw Talk / Re: Scrollsaw Association of the World
« on: June 05, 2010, 05:32:57 pm »
I agree on all that has been said and if you don't like it you don't have to belong, local club or national
Cheers
Jimbo

1900
Swap Shop / Re: Pinned end blades
« on: June 04, 2010, 09:53:30 pm »
Lay the blade flat ona piece of steel with pin just over the end and give it a sharp tap with a light hammer and the pin will either drop staight out or you can take it out easly with a pair of pliars
Jimbo

1901
General Scroll Saw Talk / Re: Spiral Blades - Attn: Charlie D.
« on: June 04, 2010, 09:44:48 pm »
I havn't tried them [to new to the saw] but as Charlie says practice the same as anything you do
Jimbo

1902
The Coffee Shop / Re: what to do when you're to sick to scroll?
« on: June 04, 2010, 09:42:26 pm »
Never to sick, the only time you cant saw is when on holiday, unless of corse you take with you, but that would be instant divorce
Jimbo

1903
The Coffee Shop / Re: Auto "Censor"!
« on: June 04, 2010, 09:39:18 pm »
What was that
Jimbo

1904
The Coffee Shop / Re: ANNOUNCEMENT!!!
« on: June 04, 2010, 09:37:53 pm »
When my new saw arives I may be a bit tied up for awhile, but if it is as good as they say it is mayby not
Jimbo
PS thanks a lot for all your nice coments

1905
Brag Forum / Re: Steve Good Videos
« on: June 04, 2010, 09:33:44 pm »
I have whatched a lot of them also I thought scrolling was easy till I tried.
Thanks Steve
Jimbo

Pages: 1 ... 125 126 [127] 128 129 ... 136

SMF

Teknoromi