1201
Brag Forum / Re: name plaque
« on: May 10, 2013, 11:42:05 am »
Awesome Plaque, what finish did you use on it?
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
1202
Brag Forum / Re: Knife#2 for the June 1 sale
« on: May 09, 2013, 05:12:36 pm »
great looking knife, I like the wood used for the handle too.
1203
Brag Forum / Re: and this is pattern cut 2
« on: May 09, 2013, 05:10:20 pm »
good looking pattern
1204
Brag Forum / Re: something new
« on: May 09, 2013, 01:18:33 pm »
beautifully done, love it. what did you use for the backer?
1205
The Coffee Shop / Re: Had a great online friend pass away this weekend
« on: May 08, 2013, 05:27:53 pm »
Sorry for your loss, as Marg says, it must be harder for you as you can't go to pay your respects. please accept my condolances.
1206
The Coffee Shop / Re: Canadien Girls
« on: May 08, 2013, 05:16:18 pm »
sounds like what happened to Rob lol
1207
The Coffee Shop / Re: Excalibur 21
« on: May 08, 2013, 05:14:57 pm »
you're going to love the new toy.
1208
Brag Forum / Re: Sailor Steals A Kiss
« on: May 08, 2013, 04:02:41 pm »
nice cutting, and great pattern
1209
General Scroll Saw Talk / Re: Am I on the right track part 2
« on: May 08, 2013, 11:53:59 am »
Great cutting and brilliant pattern - you're definately on the right track.
1210
General Scroll Saw Talk / Re: EX21 Lever Tension Problem
« on: May 08, 2013, 11:49:05 am »
There is a plastic screw in the front of the lever pivot point, this is an adjustment to lock the lever in position. I dont know the correct adjusting procedure/setting, but as you set the tension it pulls the metal clamp block up against this screw. Maybe someone here knows the correct setting procedure for it. I'll email Darren at Axminster Power Tools to see if he can send me the settings as he adjusted mine when it had same problem.
1211
Introduce Yourself. / Re: Another new one found this forum
« on: May 08, 2013, 11:43:06 am »
Hi Randall, welcome to the forum, I'm Keith from Cornwall U.K.
1212
Brag Forum / Re: A rose
« on: May 08, 2013, 11:25:16 am »
Rob, no, I wasn't reading that. was there any reason I should have been?
EIEIO, I use #1 Flying Dutchman Ultra reverse blades for 99% of my work. Every third tooth is reversed so it gives a fantastically clean cut with almost no need for sanding after cutting as you can see in the picture, and very little wander in long straight cuts. Occasionally I'll use a #3 blade (same type) but a #1 is my favourite blade. hope that helps.
EIEIO, I use #1 Flying Dutchman Ultra reverse blades for 99% of my work. Every third tooth is reversed so it gives a fantastically clean cut with almost no need for sanding after cutting as you can see in the picture, and very little wander in long straight cuts. Occasionally I'll use a #3 blade (same type) but a #1 is my favourite blade. hope that helps.
1213
Brag Forum / Re: A rose
« on: May 08, 2013, 09:10:09 am »
Merlin, I cut the green one to fit where I wanted it to, them laid it on top of the red and marked the red one and cut it to fit. Once the finish has been applied to the rose I will attatch the backers with a spot or two of glue, but they will be held in place with the backer of the frame. (hope that makes sense lol)
1214
Brag Forum / A rose
« on: May 08, 2013, 06:10:52 am »
I was asked to make a rose for someone, after a lot of sorting through various patterns I decided on this one by "Grampa", Thanks Grampa. I cut it from 3mm Birch ply and cut the backers from coloured card. there is no finish on it yet, it's just as it came off the saw. I just put it in the frame to see what it looked like. As usual all comments welcome.
Keith.
Keith.
1215
Brag Forum / Re: jeff gordon portrait
« on: May 07, 2013, 12:51:34 pm »
looks great, very nice cutting.
