1186
Brag Forum / Re: Relief Nativity
« on: October 07, 2010, 01:36:45 pm »
Nicely done!
News: Had a couple issues with the forum today. 1/19/2017. I believe I have them corrected now. Let me know if you have any trouble. Thanks.
Show Posts
This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.
1187
General Scroll Saw Talk / Re: Update: Heritage Building Spec.
« on: October 07, 2010, 01:35:52 pm »
Thanks for the update. Do you have a link to their site?
Is this it by chance?
http://www.heritagewood.com/
Is this it by chance?
http://www.heritagewood.com/
1188
General Scroll Saw Talk / Re: sales
« on: October 06, 2010, 01:17:17 am »
There are a lot of charitable organizations who could use your talent. don't give up your scrolling because of now sales. Find another venue to share your talent.
1189
General Scroll Saw Talk / Re: Air Brush suggestion?
« on: October 06, 2010, 01:15:51 am »
I have the badger 350. Be sure and get an inline filter. Lots of extra bottles.
1190
Brag Forum / Re: Some work from me......finally
« on: October 04, 2010, 06:42:22 pm »
About time you shared your talent with us mere mortals. 
Nicely done.
Nicely done.
1192
General Scroll Saw Talk / Re: I was cutting away....
« on: October 04, 2010, 06:39:03 pm »
Best wishes for an instant cure for you dangling ganglia..And a rapid and full recovery!
1193
General Scroll Saw Talk / Re: LOOKEEEEE What I Found!
« on: October 03, 2010, 02:05:14 pm »
Interesting site...Thanks for the link.
1194
Ask Steve a question. / Re: gear template generator
« on: October 02, 2010, 11:33:36 am »
Great find Andre. I hope you won't mind if I share the link on another forum.
1195
General Scroll Saw Talk / Re: A "How-To" question on making crafts???
« on: October 02, 2010, 11:30:53 am »
By placing the dado in you give greater gluing surface and alleviate the problem of two tone stains. You always have a clean surface to glue too. Place the dado after staining of course. You can do stop dadoes as well. Make the base slightly longer than the "craft" piece and insert it into dado, or use wooden dowels and they 2 parts will never come apart.
1196
General Scroll Saw Talk / Re: Blade Change
« on: October 01, 2010, 07:01:10 pm »
I've never encountered any "flying debris" when a blade breaks. I suppose it could happen. It just normally startles the crap out of me. I change the blade when I notice I'm forcing the wood or my neck or forearm muscles seem to be getting tired, or if I notice a major change in burning of the wood.
1197
General Scroll Saw Talk / Re: I'm thinking about getting a router
« on: October 01, 2010, 11:25:05 am »
Kepy,
we would love to see a some pics of your set up.
we would love to see a some pics of your set up.
1198
General Scroll Saw Talk / Re: Squaring Blade Help
« on: October 01, 2010, 12:02:45 am »
I'd definitely switch to the #5. Poplar is rather dense to begin with. And like mentioned make sure you have enough tension.
1199
Ask Steve a question. / Re: Formby's oil
« on: September 30, 2010, 06:33:18 pm »
Periodically I (I'm not Steve but) strain mine through a couple of coffee filters usually 3 to get out some sludge building up in the bottom and just keep using it and adding to it.
1200
General Scroll Saw Talk / Re: Critiques
« on: September 30, 2010, 06:30:30 pm »
Great variety and love your shop. You are very talented, thanks for sharing.
Where are you located? I'd guess Oregon since the mention of myrtle-wood.
Where are you located? I'd guess Oregon since the mention of myrtle-wood.
