Scrollsaw Workshop Community -Please register to enable posting.
General Category => General Scroll Saw Talk => Topic started by: kalipbean on October 10, 2010, 11:46:35 am
-
What does everyone do when cutting portraits or animals...etc on baltic berch do for a frame? Do ya'all make your own frame? And if so, just glue it on top of the birch? My only issue is I do not have a miter saw, but I could just cut the angles on the scroll...might not be perfect but want to see what other people do.
-
My personal choice is to 'feature' the portrait and 'understate' the frame.
When I get the chance I drop in to a "dollar store" and get an assortment of cheap frames of various sizes that I can later use by just hitting them with a couple coats of paint of the appropriate color to go with the cutting and my background sheet.
Almost all my 'background' colors come from the ScrapBook section of Michael's since they have a tremendous assortment of colors and textures.
~~~GrayBeard~~~
-
I make all my frames. I usually cut a rabbit in the back for the project to fit in. 8)
-
i buy my frames by the case from the dollar tree and use black felt to go behind the portrait. i havent mastered frame making yet.
-
If it is a wildlife, cowboy or western scene, I make my frames from barn wood or old fence pickets. My fancier frames are made from mesquite and I follow the waves of the grain to determine the outside shape. Have also just used 1 by lumber.
-
i make my own frames iv used everything from 1/4" to 2.5" depends on the size of the project. i also usually cut a rabit in the back of the fame for the project to fit into. if you dont have a miter saw you could cut them useing a handsaw an a miterbox it goes rather quick or you could cut them with a table saw or if you dont care about mitering 45s you could just cut a box frame useing 90s
-
Hey Kalipbean, I make my own frames. Like GB, I keep them understated. I usually use 1/2" x 1-1/2" of what ever I have on hand. I cut a rabbit with a dado blade on the table saw. I have a miter sled for the table saw that cuts perfect 45s. I glue the frame peices together without any reinforcement, then glue the BB directly into the rabbit. That way the frame wont fall apart. Then I will glue the backer to the BB.
P.S. Pattern by Steve Good!
-
I love the fact of making my own frame, only thing is I do not have a router or a table saw. My father has both and Im sure I could do it. What exactly would I need to do the rabbet? I can do that on the table saw? Or must it be done on a router?
-
If you have a way to cut rabbets you can make your own frames on the scrollsaw like this video.
http://www.youtube.com/user/noho91#p/a/u/2/AM-3BjC4quw
-
I love the fact of making my own frame, only thing is I do not have a router or a table saw. My father has both and Im sure I could do it. What exactly would I need to do the rabbet? I can do that on the table saw? Or must it be done on a router?
You can cut rabbits with a dado blade on a table saw or with a router in a router table. You can also cut rabbits with a rabbit plane.
-
you can cut them with a regular blade on a table saw. a standard cut is usually 3/8 by 3/8. raise
your blade 3/8, measure from fence to outside of blade 3/8. stand on edge for first pass. swap ends
place flat and make second pass. use a piece of scrap to set up saw. to make wider or deeper cuts adjust saw to fit your needs
-
I am going to have to try what they did on the u-tube video. Very Cool!
This thread poses a couple of questions. Why do you not put glass in? I use UV anti glare glass on all mine. I just cut the rabbit deep enough to hold the 3 pieces. I usually use 1/8" press board for my backers and paint them. If you are using felt and not covering it with glass - doesn't it collect dust over the years? I join my frames with pocket screws or biscuits. The problem with my method is the cost involved. People don't like paying for the frames.
-
Hey Julie, I don't use glass because It's not a paper portrait. For me, I think glass distracts from the wood. and since I make my own frames, I don't want to go out and buy glass! If you use a good top coat, It is easy to dust with a soft brush or feather duster.
-
Speaking of frames..... does anyone need new 8x10 frames with 5/16th groove (rabbit)? I got a LOTof them.
email me and we will talk.
-
Well, that's why I buy the UV anti-glare glass. I always finish my pieces. I guess I will have to try it without glass and see how it goes over. The cost of making the frames with glass is high. I sell my pieces with or without the frame and when people find out what I'm charging for the frame the often buy without.
-
Fortunately for me, I get a lot of scrap hardwoods for free from our woodworking club. The scraps come from a member who owns a wood milling co. They usually come in the form of 1-1/2 to 2-1/2" thick pieces that I have to resaw and plane. so It can be labor intensive, but it is free!
I use this wood to make frames and a lot of my scroll saw projects.