Scrollsaw Workshop Community -Please register to enable posting.
General Category => General Scroll Saw Talk => Topic started by: wha on September 23, 2012, 07:12:01 pm
-
I have this problem with my ornaments sticking together after they have been sprayed with a clear coat finish. The finish I'm using is Krylon Acrylic crystal clear. This is also happening with ornaments that have been painted as well. Also is their a way to keep them from sticking to the rack I use to set them on when I spray them.
Bill
-
I have used these Dry-It boards for years. They are available at the Artist's Club for about $11 each. I keep one for clear coating and one for other types of spraying that I do. I also have one for drying. The surface is little points that are very tiny (sharp) and nothing sticks after spraying. They are really a good investment. Here is the link:
http://www.artistsclub.com/cfTools/tools_display.cfm?id=70113 (http://www.artistsclub.com/cfTools/tools_display.cfm?id=70113)
Good Luck. Sheila
-
Sounds to me like you may have humidity problems when spraying, try extending your drying time or add heat in some way. Where are you located as far as temperatures and humidity goes?
As far as a surface for painting, you can make a bed of nails or use small pieces or strips of wood to hold items above the table surface. I have nailed long wires to the ceiling in my shop painting area (the garage) to suspend cuttings while spray painting and drying.
Just some suggestions.
Rog
-
Sounds to me like you may have humidity problems when spraying, try extending your drying time or add heat in some way. Where are you located as far as temperatures and humidity goes?
As far as a surface for painting, you can make a bed of nails or use small pieces or strips of wood to hold items above the table surface. I have nailed long wires to the ceiling in my shop painting area (the garage) to suspend cuttings while spray painting and drying.
Just some suggestions.
Rog
I'm in Nova Scotia. Even after a few months they still stick together when stacked on top of each other.
I'll look at making a bed of nails to put them on when spraying.
-
Painters pyramids work well. Any woodworkers source will have them.
-
When storing my projects, I place a piece of Wax Paper in between to keep them from sticking. 8)
-
Not to beat a dead horse but, some more suggestions.......
Are you using spray cans? If so are you mixing the paint well? Shake the can well and make that ball rattle.
Are you putting on too heavy of a coat? Use thin coats and sand with very fine grit paper between coats. Letting each coat dry well and use 400-600 grit or even heavy brown paper bag to knock off the sheen between coats.
I'm not sure about humidity in Nova Scotia but, if you could use a light bulb (lamp) or an electric space heater (DO NOT USE A FLAME OR MICROWAVE OVEN) near the item while drying may help.
Are you using an oil on the items before spraying? Some oils never dry completely (lemon oil and mineral oil come to mind) if so try using boiled linseed oil and let it dry for a few hours or a day, it will dry and fill pores too. Lemon and mineral finish on the items look good and really pop the grain but they must be wiped off very well before finishing. (or, don't put any more finish on them at all)
Last but not least, try a coat of paste wax and buff to a sheen after the finish has dried. Depending on the cutting, I think this looks the best anyway. :)
Maybe something here will help.
Rog
-
An easy idea and doesn't cost much. Take a board and hammer small nails through it so they stick out the other side. Put as many as you choose. I do this and put it on a small lazy susan so I can spin it while I spray
-
we bought a new fridge last spring. I kept the box and opened one seam and put it in the corner of my shop. I then placed a 1 inch dowel across the top. and I wraped long pieces of soft wire on the dowel and let the ends hang down. that gave me a paint booth.
-
Thanks for all the great suggestions. I made a nail bed today and i'll try the brown paper bag and see what happens.
Bill.
-
my 2 cents:
I use clear spray lacker out a can. the one that dries in 10 minutes.
in my basement the temps are about 55- 59 and that's to low for a good drying process.
small projects I dry with a hot hairdryer (think about 113F) and that dries well.
only it will not get very hard, so I let it rest in the cold basement for at least 24 hours and that will harden the lacker.
-
I made my nail bed which helped a lot and I set a fan up to blow across the ornaments while they were drying and that helped a lot as well. After they were dry to the touch I hung them up and left them for a day now they don't stick together.
Thanks for all the help.
Bill
-
I never had good success with using the Krylon clear coat varnish. Laquer or poly.
All said above is important for successfull completion of a project. Danny :+}
-
I use the Krylon all the time
Tried several other brands, but still prefer the Krylon clear. I get mine at Wally World. Price here is $3.64 price at the hardware store for the same can is $7.00 No Brainer! I use 2- 3 coats. Light sand between with 1000- 1200 grit and after the final I give it a couple swipe with 4000 grit.
-
I have a video of a an ornament on my youtube page on the Country Scroller. I painted it, didn't have much trouble with it. Sometimes if I paint something and it is humid out, it is sticky for a while.http://www.youtube.com/watch?v=BrnWLMxCQn8&feature=plcp (http://www.youtube.com/watch?v=BrnWLMxCQn8&feature=plcp)
-
Sprayed some puzzle pieces earlier this morning and still waiting for them to be dry to the touch. Humidity is 84%. Things painted like this in lower humidity are usually dry to the touch in 10-15 minutes. At least today when folks ask what I'm doing I can answer Drying Paint~!